Bio-rad ChromLab™ Software Manual de usuario Pagina 78
- Pagina / 178
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3 | Setting Up NGC Chromatography Systems
76 | NGC Chromatography Systems and ChromLab Software
Connecting the Power and Communication Cables
The power sockets and communication ports for the NGC system are located on
the back of the instrument. Because the back of the instrument will be very close to
the back of the standard cold cabinet, it is recommended that you connect the
power and communication cables before lifting the instrument into the cabinet.
Note: The Cat 6 ethernet cable to connect the NGC instrument to the
computer running Chr
omLab™ softwar
e is approximately 10' (3.0 m) in length.
L
EGEND
1 Power on/off switch 2 Fuse cover
3 Power inlet port 4 Power outlet ports
5 Ethernet connection port 6 Touch screen connection port
- Chromatography Systems 1
- Software 1
- Installation Guide 1
- NGC™ Chromatography 3
- Systems and 3
- ChromLab™ Software 3
- Table of Contents 5
- Installation Guide 7
- 1 Introduction 9
- Main Features 10
- Safety Information 11
- Regulatory Information 12
- FCC Warning and Notes 13
- Finding Out More 14
- 2 Preparing Your Site 15
- Item Specification 16
- Room Requirements 17
- Environment 18
- Power Requirements 19
- ChromLab System Requirements 20
- Installation Guide 21
- To turn off automatic updates 22
- To change the font size 22
- 3 Setting Up NGC 23
- Chromatography Systems 23
- NGC Systems Accessories Kit 24
- NGC Scout Accessories Kit 25
- NGC Discover Accessories Kit 25
- Attaching the Touch Screen 26
- Installation Guide 27
- Installation Guide 29
- Installation Guide 31
- Installation Guide 33
- Installation Guide 35
- Installation Guide 37
- Stand kit (#788-5040) 38
- Installation Guide 39
- Installation Guide 41
- Installation Guide 43
- To install the pH probe 44
- Installation Guide 45
- Installation Guide 47
- Upper expansion tier 48
- Previously attached 48
- Installation Guide 49
- Installation Guide 51
- Task: Refer to the section: 52
- Inserting Additional Modules 53
- Installation Guide 55
- Installation Guide 57
- Connecting the Air Sensors 58
- Installation Guide 59
- Installation Guide 61
- UV monitor 62
- Installation Guide 63
- Connecting the Air Sensors 64
- (air sensor to pump inlet) 65
- To activate the air sensors 67
- Installation Guide 69
- Installation Guide 71
- Installation Guide 73
- Installation Guide 75
- Trigger wire 77
- Positive 77
- Installation Guide 79
- Installation Guide 81
- 4 Installing ChromLab 83
- Software 83
- Installing ChromLab Software 84
- The wizard installs ChromLab 85
- Software and the NGC Systems 86
- Installation Guide 87
- Setting the System Name 88
- Installation Guide 89
- On the ChromLab Computer 90
- ChromLab computer 91
- On the NGC Instrument 92
- Installation Guide 93
- Setting Delay Volume 95
- Installation Guide 97
- 5 Plumbing and Priming the 99
- Buffer Bottles 100
- Waste Bottles 100
- Plumbing NGC Systems 101
- Plumbing All NGC Systems 102
- Sample Pump Wash Line 103
- System Pumps Wash Lines 103
- To plumb the sample pump 105
- Installation Guide 107
- Plumbing the NGC Quest System 108
- Installation Guide 109
- To plumb the system pumps 110
- Plumbing the NGC Scout System 111
- To plumb the pH valve 113
- Installation Guide 115
- Tubing color Port Solution 117
- Installation Guide 121
- Plumbing Sample Inlet Valves 122
- Plumbing Outlet Valves 123
- Installation Guide 125
- To prime the system pumps 126
- To purge the system pumps 127
- Priming the NGC Scout System 129
- Purging the NGC Scout System 131
- Priming NGC Discover Systems 133
- Installation Guide 135
- To prime the sample pump 137
- Installation Guide 139
- Installation Guide 141
- To purge the sample pump 143
- Installation Guide 145
- Calibrating the Instrument 146
- To zero the pressure 147
- A Upgrading ChromLab 149
- Updating NGC Systems 150
- Installation Guide 151
- B Troubleshooting ChromLab 153
- Possible Cause Solution 154
- Installation Guide 157
- Installation Guide 159
- Installation Guide 161
- Installation Guide 163
- NGC ChromLab Application 164
- Firmware Update Failure 165
- C Connecting the C-96 167
- Installation Guide 169
- To prepare the tubing 170
- Autosampler 171
- Sample Inject 171
- Installation Guide 173
- D Firewall Configuration 175
- Life Science 178
- Bio-Rad 178
- Laboratories, Inc 178
Relacionado con productos y manuales para Instrumentos de medición Bio-rad ChromLab™ Software
Instrumentos de medición Bio-rad BioLogic QuadTec™ Detector and Components Manual de usuario
(58 paginas)
(58 paginas)
Instrumentos de medición Bio-rad LP Data View Software for BioLogic LP System Manual de usuario
(4 paginas)
(4 paginas)
Instrumentos de medición Bio-rad LP Data View Software for BioLogic LP System Manual de usuario
(5 paginas)
(5 paginas)
Instrumentos de medición Bio-rad Profinia™ Protein Purification Instrument Manual de usuario
(4 paginas)
(4 paginas)
Instrumentos de medición Bio-rad Profinia™ Protein Purification Instrument Manual de usuario
(2 paginas)
(2 paginas)
Instrumentos de medición Bio-rad Profinia Protein Purification System Accessories Manual de usuario
(1 paginas)
(1 paginas)
Instrumentos de medición Bio-rad Profinia Protein Purification System Kits Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales